產品名稱(Product name)：機器人自動澆鑄系統  Robot automatic casting system

產品類別(Product category)：自動澆鑄  Automatic casting

應用方向(Application direction)：主要用于水暖、五金、泵閥、消防、汽摩配件等的重力澆鑄  

Mainly used for gravity casting of plumbing, hardware, pump valves, fire fighting, automobile and motorcycle accessories, etc.

產出品分析(Output product analysis)：生產醫療機械、廚具、汽車零配件、電氣配件、水龍頭、消防部件、泵閥、管件、機械配件等農機配件、爐具配件、機床部件、汽摩配件、五金配件等  

Production of agricultural machinery parts, stove parts, machine tool parts, automobile and motorcycle parts, hardware parts, etc.

工序組成(Process composition)：腳踏開關（第一次需要）→模具旋轉→人工放置砂芯→腳踏開關→合�！�等待機器人手右工位澆鑄完成信號→澆鑄機旋轉→自動開模→人工取產品→腳踏開關→模具下降浸入冷卻液  

Foot switch (needed for the first time)→mold rotation→manual placement of sand core→foot switch→mold closing→waiting for the signal of completion of casting at the right station of the robot hand→casting machine rotation→automatic mold opening→manually take product→foot switch →The mold is lowered and immersed in the coolant

選材用料(Material selection)：

1、整體機架采用QT450鑄造件，不易變形，韌性好

1. The overall frame adopts QT450 castings, which are not easy to deform and have good toughness;

2、潤滑部分要注入通用鋰基脂滴點是193℃，工作錐入度是240的3＃通用鋰基脂潤滑油，它比2#更耐高溫，用于載荷較重或立式電機軸承的潤滑�？鼓ヒ簤河蜑�68＃，新機三個月更換一次，以后每八個月更換一次

2.The lubricating part should be filled with general lithium grease with a dropping point of 193°C and a working penetration of 240. It is more resistant to high temperature than 2# and is used for the lubrication of heavier loads or vertical motor bearings. . The anti-wear hydraulic oil is 68#, which is replaced every three months for the new machine, and every eight months thereafter;

3、冷卻池中的冷卻液成分為石墨粉和水（約850L）

3、The composition of the coolant in the cooling pool is graphite powder and water (about 850L);

4、合模架經過高頻淬火，鍍鉻處理，提高表面硬度，經久耐用

4、The clamping frame is high-frequency quenched and chrome-plated to improve the surface hardness and be durable;

5、電路由PLC控制，數據設定采用觸摸顯示屏，液壓元件全部進口

5、The circuit is controlled by PLC, the data setting adopts a touch screen, and all hydraulic components are imported;

6、配置歐姆龍感應器，控制合模精度，故障率低

6、Equipped with Omron sensor to control the accuracy of mold clamping, with low failure rate;

7、采用伺服電機控制，可以通過plc來量化升降角度

7、Using servo motor control, the lifting angle can be quantified through PLC;

8、采用行星齒輪減速機，扭矩大，承受能力強

8、Adopt planetary gear reducer, with large torque and strong bearing capacity.

機能價值(Functional value)：

1、采用人機界面，狀態實時顯示，菜單輸入，工藝參數調整范圍廣獨立的控制系統，參數存儲智能化，故障易查操作簡單，維護成本低

1、Adopt man-machine interface, real-time status display, menu input, wide range of process parameter adjustment, independent control system, intelligent parameter storage, easy fault checking, simple operation, low maintenance cost;

2、采用上下合模，模具轉動，使金屬液體能均勻分布，避免出現冷隔、澆不足和氣孔等缺陷

2、The upper and lower molds are clamped and the mold rotates to make the metal liquid evenly distributed, avoiding defects such as cold barriers, insufficient pouring, and pores;

3、冷卻液為石墨粉與水的混合液體，石墨粉附著于砂芯上，容易脫模，且不溶于水，具有耐高溫性能

3、The cooling liquid is a mixed liquid of graphite powder and water. The graphite powder adheres to the sand core, which is easy to demould, is insoluble in water, and has high temperature resistance;

4、通過預制砂芯，可以鑄造帶腔體的零部件，內腔表面光滑，能實現高難度鋁鑄件的鑄造、加工；內部無瑕疵，廣泛應用于對結構性能、氣密性能、內外部等要求較高的汽車零部件、機械零部件等產品

4、Through prefabricated sand cores, parts with cavities can be cast. The surface of the cavity is smooth, which can realize the casting and processing of difficult aluminum castings. The interior is flawless, and it is widely used for structural performance, air tightness, internal and external requirements. High-end auto parts, mechanical parts and other products;

5、自帶風箱，散除熱量，節能環保，保障設備正常運轉

5、Comes with a wind box to dissipate heat, save energy and protect the environment, and ensure the normal operation of the equipment;

6、傾斜角度范圍為0°-90°

6、The tilt angle range is 0°-90°;

7、可靠性強、穩定性高、正常運行時間長

7、Strong reliability, high stability, and long uptime;

8、速度快，澆鑄工藝決定了操作周期時間短

8、The speed is fast, and the casting process determines the short operating cycle time;

9、機械臂型號和品牌的選擇更多樣

9、More choices of robot arm models and brands;

10、合模緩沖裝置，保護砂芯和模具

10、Clamping buffer device protects the sand core and mold.

創意設計(Creative design)：

1、機器人代替人工澆鑄，安全可靠

1、Robots replace manual casting, which is safe and reliable;

2、機械手臂定量澆鑄金屬液體，精度高，不易浪費，金屬液損耗少，提高經濟效益

2、The mechanical arm casts liquid metal quantitatively, with high precision, not easy to waste, less metal liquid loss, and improved economic benefits;

3、固定左工位進行人工操作，操作便捷，符合人體工學設計

3、Fixed left station for manual operation, convenient operation and ergonomic design;

4、創新雙工位澆鑄技術，優化加工工序，提升生產效率

4、Innovate dual-station casting technology, optimize processing procedures, and improve production efficiency.

信譽價值(Reputation value)：

1、國內自主技術產權，產品使用穩定有保障

1、Domestic independent technical property rights, product use is stable and guaranteed;

2、全球服務網絡，客戶服務快捷便利

2、Global service network, fast and convenient customer service;

3、支持個性化定制，提升客戶體驗感

3、Support personalized customization to enhance customer experience;

4、二十余年的品牌積淀，企業情感認同高

4、More than 20 years of brand accumulation, high corporate emotional recognition;

5、專家型技術人員全程服務，產品設計合理有效

5、Expert technicians provide full service, and the product design is reasonable and effective.